This lightweight, high-pressure rim tape offers great protection against spoke hole flats and is easy to install. This Italian-made tape is light and thin, so it will not inhibit tire fitting. Nylon elastic material is used to ensure a snug fit without movement.

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Schwalbe High Pressure Rim Tape effectively protects the tube against mechanical damage. - Elastic for ease of installation - High pressure: 8 bar / 116 psi

The Muc-Off Tubeless Rim tape is made from their proprietary performance material with a pressure-sensitive adhesive to provide just the right amount stretch whilst maintaining durability and strength needed to create a lasting airtight seal. Semi-transparent material makes locating the valve hole easy.

- 6061-T6 aluminum lever construction - Cr-Mo axle - Road 100mm/130mm - MTB 100mm/135mm - 110g

The Cinema VF (uniVersal Front) hub guard is injection molded from an ultra-durable and fast sliding nylon composite. Designed to work with as many different front hub and fork combinations as possible, the VF guard covers either side of your hub and fork dropouts to protect them during grinds. Simply install outside the fork dropout, without replacing any hub hardware and without spacing out your forks. - Material: Nylon - Fits: Most Front Hubs - Weight: 0.9 oz

The Cinema VR (uniVersal Rear) hub guard is injection molded from an ultra-durable and fast sliding nylon composite. Designed to work with as many different rear hub and frame combinations as possible, the VR guard covers the drive side or non-drive side of your rear hub and protects it from grinds. Simply install outside the frame dropout without replacing any hub hardware and without needing to space out your frame. - Material: Nylon - Fits: Most Rear Hubs - Weight: 1.2 oz

A simplified quick release, utilizing an exposed/external split cam that straddles the end of the skewer. - Lighter and both easier and less expensive to manufacture, these external cam quick release levers represent an excellent value - Fits both road and mountain bike frames & forks with 100/130/135mm hub spacing - Construction: Chromoly steel skewer with alloy cam/lever and plastic/steel acorn-nut - Sold as a front & rear matching pair - Lengths: 133mm (FR) / 169mm (RR) - Weight: 58g (FR) / 64g (RR)

A modern take on the classic internal/enclosed cam design as invented by the late, great Tullio Campagnolo. - Internal cam design exerts a far greater vise-like grip vs. external/exposed cam QR lever designs for a more secure fit - Fits both road and mountain bike frames & forks with 100/130/135mm hub spacing - Construction: Chromoly steel skewer with alloy lever and plastic/steel body & acorn-nut - Sold as a front & rear matching pair - Lengths: 133mm (FR) / 169mm (RR) - Weight: 57g (FR) / 61g (RR)

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA 7075 T6 Aluminum

The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA - 7075 T6 Aluminum - Similar to Fox Kabolt axle

The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA - 7075 T6 Aluminum

Boostinators are hub specific conversions designed to take non-boost hubs and convert them to boost compatibility. Don't toss out that wheelset - Boostinate it.

Boostinator kits allow non-boost wheels to be mounted in Boost spacing frames and forks. While incremental, the benefits of the "Boost" 15x110mm front and 12x148mm rear axle standards are clear: better clearance for fatter tires & rims and reduced dish for stiffer, stronger wheels. The big bummer? Taking full advantage requires not only a new frame and fork, but new wheels as well. In response, we have developed the Boostinator. When paired with compatible 15x100mm or 12x142mm hubs, Boostinator kits allow existing wheels to be mounted in Boost-standard frames and forks. Disc and drivetrain positions are maintained and, thanks to a quick re-dish, spoke bracing angles are improved. Boostinator kits consist of a specially-designed axle end cap and, in the case of rear kits, a precision-machined rotor spacer with a set of six high-strength bolts. In keeping with Boost specifications, the disc and cassette are shifted outboard, allowing brakes and derailleurs to function as designed. Compatibility: - Front boostinators are only an endcap and do not require a rotor spacer. The wheel is re-dished. - Rear boostinators require both a re-dish and rotor spacer. - Rear Boostinator kits are not approved for rotors larger than 183mm. - Hubs spacing is 100mm front and 142 rear, and the Boostinators make them 110 and 148 respectively. - Compatible with 6-bolt FRONT wheels and SOME centerlock models. - Compatible with ONLY 6-bolt REAR wheels (there is no way to space centerlock rotors over 6mm). - NOT recommend (or safe) for non-symmetric lacing like the 2:1 lacing found on some of Industry Nine's wheels. *Note: You will need to re-dish your wheel after installing any Boosinator. Boostinator DR: - The Boostinator DR is compatible with DT-Swiss 12x142mm Star Ratchet (240- and 350-series) rear hubs with 6-bolt (IS) rotor mounts. - Centerlock hubs are not supported. - 180- and 190-series hubs are Centerlock only. - The Boostinator DR is also compatible with some complete wheels from DT Swiss, Roval (Specialized), Giant, Syncros (Scott), and others that use DT's Star Ratchet internals. - Remove the disc side end cap. Bearing size 6802 15x24. - Net weight: 18g Boostinator HR: - The Boostinator HR is compatible with 12x142mm Hope Pro 2 EVO and Pro 4 rear hubs. - Non-EVO Pro 2 hubs are not supported - Net weight: 18g Boostinator 9TR: - Compatible with 142x12 rear Industry Nine Torch hubs. - Not compatible with 2:1 lacing wheels from Industry Nine - Not compatible with Centerlock hubs Tech Specs: - Material: 6061 aluminum - Included: Rear kits come with appropriate-length Class 10.9 bolts, each roughly 40% stronger than more common Class 8.8 hardware.

125 piece assortment of precision machined axle spacers (0.5mm to 5mm thickness). - Outside Diameter of Spacers: 16mm - Inside Diameter of Spacers: 10mm Kit includes: - (10) - 0.5mm thick spacers - (30) - 1mm thick spacers - (30) - 2mm thick spacers - (25) - 3mm thick spacers - (15) - 4mm thick spacers - (15) - 5mm thick spacers

Wheels Manufacturing Axle Spacers help you dial in your hub spacing to ensure correct fit and side-to-side spacing in the rear triangle without having to alter the wheel's dish. - Spacers come in bags of 20

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 126mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 137mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 130mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 141mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs with 126mm spacing - Type: Hollow Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 137mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese front hubs - Type: Hollow Axle - Threads: 9mm x 1 - Diameter: 9mm - Length: 110mm - 1 axle per bag

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Front 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Diameter: 14.8mm - Length: 10.6mm - 1 cone per bag - Note: O-ring / seal not included. COMPATIBLE HUBS: - Shimano HB-C201 Front - 105 HB-1050 Front - Deore LX/Mtn LX Front - STX HB-MC32/30 Front - Shimano HB-A410, HB-A416 Front

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Front 9mm x 1 axle - 22mm metal dust seal is pressed on cone - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Cone Diameter: 15.0mm - Dust Seal Diameter: 22mm - Length: 11.4mm - 1 cone per bag COMPATIBLE HUBS: - Shimano Nexave HB-T400 Front - Shimano Deore HB-M510 Front - STX HB-MC32/30 Front - STX Parallax Front

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: Joytech 9mm x 26, front hub - Compatible with 9mm x 26 axle - Cone Wrench Size: 13mm - Threads: 9mm x 26 - Diameter: 15.0mm - Length: 12.8mm - 1 cone per bag - Note: O-ring / seal not included. COMPATIBLE HUBS: - Joytech 9mm x 26, front hub - Taiwanese hubs with 9mm x 26 axle - 105 SC 1055 8-speed Rear - 105 SC 1056 7-speed Rear - XT-II M732 7-speed Rear

Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10

Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually

Wheels Mfg. axles are made from aircraft quality 4130 alloy steel, made specifically for them. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many tandem hubs - Hollow Axle - Type: Quick release - Sold individually

Get your WeThePeople Arrow Front Hub Axle/Cone Set and freshen up that front end that's a little wobbly after that last time you cased it on the spine.

Did you trash the front bearings on your WeThePeople Arrow front hub? It happens, that just means you're riding a lot. Fear not, we've got you covered with this bearing set from WeThePeople.

Keeping the front wheel securely on the bike is kinda important. This WeThePeople Arrow Front Hub Female Bolt Set keeps your wheel right where it belongs. Sticking the nose manual is up to you.